REPAIR AND MAINTENANCE Differential (axle) CAR

• Real Axle Housing, this section can be regarded as the foundation of heavy cargo car, because of its rear wheel section, especially on the charge car or minibus. At the mini buses are rarely found these parts bent, crooked if it happens then it is caused by the collision. In this section the truck often found swelling. This is caused by a charge in excess capacitance. Crooked this section will damage the axle axle even damage the teeth. To avoid this it is in giving the charge on the car should consider the condition of a rear. If a differential housing until it touches the touch, the risk is very large crooked.

• Gaskets. As part of the axle to prevent leakage of oil is also an important part. If the leak will result in tooth axle lubrication imperfect tail damage to the axle gear. Use a standard gasket or drawing paper, do not use thick cardboard.

• Differential Carrier. Differential tooth attached to this section. To reset or replacement of part of this new gear is released from the differential housing. Once cleansed of remnants of oil and then mounted on tanggem. To unload and set up this section need specific instructions.

• Differential Ring Gear and Drive pinion gear kit. Named for the repair kit because the differential enough to replace these parts. On some cars a lot of counterfeit goods. The price difference far. Although not all counterfeit goods is bad but you need to be careful to buy this kit. Fuss also generally store would not accept back teeth that have been tried, although the setting is still sound. Then it is better to buy the original. For more secure again, down to the garage your vehicle dealer because they will pair the original and provide a guarantee for a certain period of time or miles. Since the price differential kit is expensive then it is highly advised not easy to decide to dismantle the symptoms when you hear a sound. To ensure better you try to run a car on a flat road. At speeds of 40 served until 80 kilometers / hour, note; if the teeth on each axle is damaged then there is the sound speed and time of releasing the gas pedal the sound of the first models appeared lost and the second sound model. The sound can also be caused by damage to the bearing surface of the wheels and tires. Noise caused by both this section and is clearly another at speeds 80 to 100 km / h transmission gear you free.

It is important before the dismantling of this section, conduct thorough research. Lack of experience could lead to the restoration effort does not meet the desired results. Then the examination of the causes of noise such as tire and wheel bearings as well as the sound of the exhaust needs to be examined one by one. 

• Part of this carrier differential to fasten one side of the bearing ring gear. Screw in this section allows a mechanic to set the tangent plane with the drive pinion. Adjustment results from this section can not directly be because if you look good field that does not intersect the adjustment must be repeated from the first again to remove the drive shaft. It's just a brief overview of the complexity of differential tuning cars.

• Both fasten the drive shaft bearings should be replaced if there is time to disassemble the dots appear black or blackish in color is due to continue to use bearings such good results that have been setting will change to loose again and accelerate the wear of the bearing material, the result would make the drive shaft forward and backward and damaging the tangent plane of the ring gear with the drive gear.

• Oil seals are located at the end of this function of the differential housing does not prevent the oil runs out. If you find around these parts are wet due to seepage of oil should immediately replace the new seal. Remove the propeller shaft and loosen the nuts that fasten the drive gear. To remove this nut should use the torque wrench. Consider for the moment need to be loosened how kg/cm2. It is important for reassembling. Hardness should be the same. Because of different magnitude was different then the lock violence. If you are in doubt you should ask the car dealer. Pairing this seal should sit well and flat. Clean the carrier so that the time differential seal leak did not enter. May also use a little liquid gasket on the outer side of the seal. In the old car, it can happen that although the installation procedure is correct but the oil still leaking. Next need to pay attention to the Universal Joint Flange.

• Universal joint flange is the part that went round the propeller shaft to the differential besides that it also functions as a cap so that oil does not come out. This section is always rotating shaft in accordance with proper rotation. Although made of steel it is also eaten by the seals wear out a tip mounted on a differential carrier. This is why oil continues to come out even after replacing with new seals. To cope with this condition usually releases per the existing mechanic to seal and make it shorter. At first glance can be overcome but not completely, because it forced the rubber match your part that had shrunk. The safest course of action by replacing the new flange. The author recommends doing two actions: First, install the new seal is not exactly on the old seal holder. That is shifted forward or backward about 1 mm. Both sides of the flange is made of 1 mm shorter as well, or put a ring of steel as thick as 1 mm (must ring steel) at the end. This action is also intended to shift the worn area is no longer in contact with the seal. With this action better results.

• Differential pinion gear or a mechanic called satellites. These teeth are arranged on the speed cornering as the car left and right wheels can be mutually adjust the self. Wheels on the angle of rotation must be slower than the round the outside. Wear on these teeth usually cause symptoms in a car when you leave or while walking if you want to add speed or slow down any noise due to looseness. This could be caused by worn out as his or specer pinion. Mechanic is usually overcome by replacing as new and give a thicker layer on its side gear.

• Fastening the drive shaft nut is often overlooked. It did not occur to check if still buttoned properly, especially on the car load. If the nut is loose will cause the drive shaft to move forward and backward. As a result of this movement then there is change in the field of allusions to the ring gear with the drive shaft. At first will occur the hum and someday even the teeth can fall out in the differential. Highly recommended for large trucks every 3 to 6 months to check the violence of this nut and every year on light vehicles. Differential well maintained can last a long time by itself does not need to drain your pockets.

Often batteries come up short Cause / Out

battery is a source of electrical power which is certainly the beginning of the car to start the engine needs to be lit, because without electrical energy storage batteries are certainly an alias using the technology to use the manual crank or the push crowded - crowded

Age the use of battery generally depends on how the use and maintenance of users, to use the correct and well maintained can last typically 3-4 years, but that could careless use of which only less than 2 years.

If we often have short battery / electric runs out of course there are things that trouble and we need to check again, Some Causes of battery often come up short / out, among others:

 
1. Electrical system is ON steadily.

2. Unbalanced load & Charging.

3. Age battery.

Come on, Clean the Car Glass

Cleaning the windshield instead of just making more sleek or beautiful. Without realizing it, the glass looks clear that will help your visibility while driving. View more clearly, especially at night to eliminate the effects of light refraction from the outside. No need to spend a long time to make it happen, our scout car so you make the glass clear and clean.

 

Before starting, you should know that most glass cleaners contain ammonia. Compounds of nitrogen and hydrogen (NH3) is often used because it is very potent mixture of mushrooms and plaques to disappear as a result of dirty water which has dried up old or used animal dung. 

 

But beware, not all match the original glass car (Japan, Korea or Europe). Types of tinted windows is not in accordance with the application materials. The effect is not so clear glass, frosted as it adds info that we quoted from auto geek. To know the specifications of your car's glass, can be seen in the bottom corner. Also you see in the product label says "ammonia free" or "safe for tinted windows".
This step-by-step glass cleaning

1. Clean the windshield using clean water.
2. Make sure you wash and polish the glass is protected from the sun's heat can cause the soap cleanser left residue resulted in the emergence of flex on the glass surface.
3. Use a microfiber cloth to get the most out during polishing, if no, can use regular fabric.
4. Rub or spray the glass to be cleaned using the drug and then wipe with a cloth until the visible nodes.
5. Rinse the area with water. Continue until all the glass well polished.
6. FIRST windshield because it has a high degree of difficulty. Do not worry when the drug was polishing the glass touches the car body, quickly rinse the surface with water so as not to damage the paint.
7. Repeat the above process if you feel not get maximum results.
8. Read some of the rules on glass cleaner because there are certain specifications that must be considered even though in general all have the same step.

Selecting and Restoring Rim Steering

Each four-wheeled vehicles, like jeeps equipped definitely aliaswheel steering. Device which is the regulator of the bow of the vehicle. Sometimes it makes sense factory default does not feel right, so the steering wheel was replaced with another vehicleowned by, or using aftermarket products.

Former steering widely used as an option. Not just another vehicle stolen goods, but also many types of aftermarket glance. Not infrequently, the steering wheel is estimated, either aftermarket , in poor shape. Understandably, used goods. However, it does not mean having to give up. There is a solution how to pick upmerekondisinya.

Of raw materials, there are three kinds of steering wheel. The first,which is made of hard plastic, both are made from synthetic rubber,and last, is the kind that bandaged. This last special lot in commonwith this type of rubber material, but some are using polyurethan,which is more dense than the rubber material. To finish with aleather wrapped steering wheel.
In general, three types of election tricks are about the same wheel.However, since different materials used, would have been way toospecific.

• The first thing to note is symmetrical. It's absolutely on the three types of steering wheel. This type of plastic steering wheel if crooked and not symmetrical, there is little possibility to return to normal conditions. The material used is flexible and the possibility of brittle, the surface of the steering wheel will be damaged during the repair process. Rubber wheel has a rubber-coated iron frame with a way to print. If bent or not symmetrical, the greater his chances to return to its original position. Rubber material with which to adjust the iron frame is bent, although the process must be careful to not damage upholstery. This type of dressing has structure similar to the type of rubber, so it was relatively equal treatment and the possibility to recover the same.

• The surface of the wheel usually use orange peel pattern, although some are using a suede leather. Being on the type of dressing,usually leather, suede or leather semi materials. The more coarse the pattern of orange peel, the better. Reaction palms sweat and friction make a surface smooth or even damaged. This condition can not be repaired, except coat the back with leather or semi-leather, but only type of stem diameter rubber wheel usually be larger.

• Check the density of the material, especially for the type of rubber.Checks by twisting the steering rod, if it feels loose rubber that wraps can be sure the iron is not attached to the chassis. There is not the right solution to solve this problem. As for the type of hard plastic and the type of dressing these conditions do not apply.

• The similarity of the spline is the last part that must be considered.Inequality and the number of spline diameter steering wheel make the dream failed to install. But do not worry, this condition can be negotiated through service workshop lathe.